SiPy

Basic connection

Exp Board 2.0

• Look for the reset button on the module (located at a corner of the board, next to the LED).

• Locate the USB connector on the expansion board.

• Insert the SiPy module on the the expansion board with the reset button pointing towards the USB connector. It should firmly click into place and the pins should now no longer be visible.

Exp Board 3.0

• Before connecting your module to an Expansion Board 3.0, you should update the firmware on the Expansion Board 3.0. Instructions on how to do this can be found here.

• Look for the reset button on the module (located at a corner of the board, next to the LED).

• Locate the USB connector on the expansion board.

• Insert the SiPy module on the Expansion Board with the reset button pointing towards the USB connector. It should firmly click into place and the pins should now no longer be visible.

Pytrack/Pysense/Pyscan

• Before connecting your module to a Pysense/Pytrack/Pyscan board, you should update the firmware on the Pysense/Pytrack/Pyscan. Instructions on how to do this can be found here.

• Look for the reset button on the SiPy module (located at a corner of the board, next to the LED).

• Locate the USB connector on the Pysense/Pytrack/Pyscan.

• Insert the module on the Pysense/Pytrack/Pyscan with the reset button pointing towards the USB connector. It should firmly click into place and the pins should now no longer be visible.

USB UART Adapter

• Firstly you will need to connect power to your SiPy. You will need to supply 3.5v-5.5v to the Vin pin.

Do not feed 3.3v directly to the 3.3v supply pin, this will damage the regulator.

• The connect the RX and TX of your USB UART to the TX and RX of the SiPy respectively.

Please ensure you have the signal level of the UART adapter set to 3.3v before connecting it.

• In order to put the SiPy into bootloader mode to update the device firmware you will need to connect P2 to GND. We recommend you connect a button between the two to make this simpler.

WiFi

Note: This method of connection is not recommended for first time users. It is possible to lock yourself out of the device, requiring a USB connection.

• In order to access the SiPy via WiFi you only need to provide 3.5v - 5.5v on the Vin pin of the SiPy:

• By default, when the SiPy boots, it will create a WiFi access point with the following credentials:

  • SSID: sipy-wlan

  • password: www.pycom.io

• Once connected to this network you will be able to access the telnet and FTP servers running on the SiPy. For both of these the login details are:

  • username: micro

  • password: python

Antennas

Sigfox

If you intend on using the Sigfox connectivity of the SiPy you must connect a Sigfox antenna to your SiPy before trying to use Sigfox otherwise you risk damaging the device.

• Firstly you will need to connect the U.FL to SMA pig tail to the SiPy using the U.FL connector on the same side of the SiPy as the LED.

• If you are using a pycase, you will next need to put the SMA connector through the antenna hole, ensuring you align the flat edge correctly, and screw down the connector using the provided nut.

• Finally you will need to screw on the antenna to the SMA connector.

WiFi/Bluetooth (optional)

All Pycom modules, including the FiPy, come with a on-board WiFi antenna as well as a U.FL connector for an external antenna. The external antenna is optional and only required if you need better performance or are mounting the FiPy in such a way that the WiFi signal is blocked. Switching between the antennas is done via software, instructions for this can be found here.

Deep Sleep current issue

The LoPy, SiPy, and WiPy 2.0 experience an issue where the modules maintain a high current consumption in deep sleep mode. This issue has been resolved in all newer products. The cause for this issue is the DC to DC switch mode converter remains in a high performance mode even when the device is in deep sleep. The flash memory chip also does not power down. A more detailed explanation can be found here.